How to Measure, Cut, & Bend Emt Conduit | Galco
Today we will be demonstrating how to measure, cut, and bend a piece of EMT conduit to your desired length and angle.
Begin by measuring the length of conduit that you will need.
Next, you will need to measure the amount of extra conduit length required, also known as “deduct length”, as you lose some length due to the conduit bend.
After determining the amount of “deduct” length and cutting to the size necessary, you should remove burrs from the cut end of the conduit using a conduit reamer or knife.
Your bender will typically have three or four distinctive marking features, 10,45,60, and 90.
Slide the conduit into the bender leaving the appropriate amount past the arrow on the bending shoe.
Now, pull the bender handle towards you to create the bend with a firm and steady motion to avoid any kinks or crimps in the conduit.
Bend until you have reached your desired corner angle.
http://www.galco.com/get/Conduit
http://http://www.galco.com/buy/Gardner-Bend...
Music By: / dcuttermusic
Sign up for Galco’s newsletter that features our newest products, our can't-miss deals, our best videos, and total access to Galco’s electronics expertise: http://www.galco.com/email/
Connect with us!
/ galcoindustrial
/ galcoindustrial
/ galcoindustrial
/ galco-industrial-electronics
Don't forget to like and comment on this video, and subscribe to our channel!
Galco is a Factory Authorized Stocking Distributor for Over 200 Brands of Industrial Electrical & Electronic Automation, Controls and Component Products; On-Site and Send-In Repair Services for Industrial Control & Automation Products for Over 2,000 Brands; Engineered Systems Integration, Retrofits & Upgrades for Variable Speed Drives, CNC, PLC Systems, Dynamometers & Test Stand Applications. Visit us online at http:// www.galco.com or call us at 800-337-1720.
http://www.galco.com/safety
With respect to the usage, installation or assembly of any products described in this video, Galco Industrial Electronics, Inc., a Michigan corporation, encourages you to follow the requirements and/or guidelines of: i) the Occupational Safety and Health Act of 1970, Public Law 91-596, as amended, and all laws, rules and regulations implemented in relation thereto; ii) the National Electric Code®; and iii) NFPA 70E®. Any installation, assembly or work described in this video should be performed by a qualified licensed electrician.
GTV, Galco, galco.com, Galco Industrial Electronics, and Galco Industrial Electronics, Inc. are registered and/or pending registered trademarks under the U.S. Patent and Trademark Office, assumed names, registered domain names, and/or trade names of Galco Industrial Electronics, Inc., a Michigan corporation.
LEGAL DISCLAIMER:
While we have made every attempt to ensure that the information provided is accurate and has been obtained from reliable sources, Galco is not responsible for any errors or omissions, or for the results obtained from the use of this information. All information is provided "as is", with no guarantee of completeness, accuracy, timeliness or of the results obtained from the use of this information, and without warranty of any kind, express or implied, including, but not limited to warranties of performance, merchantability and fitness for a particular purpose. At all times you should defer to the instructions and safety guidelines issued by the manufacturer. In no event will Galco, its agents or employees thereof be liable to you or anyone else for any decision made or action taken in reliance on the information provided to you or for any consequential, special or similar damages, even if advised of the possibility of such damages.
Смотрите видео How to Measure, Cut, & Bend Emt Conduit | Galco онлайн без регистрации, длительностью часов минут секунд в хорошем качестве. Это видео добавил пользователь GalcoTV 22 Август 2018, не забудьте поделиться им ссылкой с друзьями и знакомыми, на нашем сайте его посмотрели 391,17 раз и оно понравилось 2.1 тысяч людям.