Easy way of connecting Raspberry Pi to laptop using Ethernet cable | Beginner Guide
Use laptop/desktop screen for Raspberry Pi.
This video solves your questions such as:-
How to connect Raspberry Pi3 to laptop?
How to use the laptop screen as a display for Raspberry Pi?
How to use Ethernet cable with Pi to connect it to laptop?
How to setup SSH on Pi?
How to make SD card bootable for Raspberry Pi3?
How to use VNC viewer/Xming with Raspberry Pi?
Beginner guide to Raspberry Pi
How to get started with initial setup of Raspberry Pi?
Hardware requirement:-
Raspberry Pi3 - buy from http://fkrt.it/zQRMbnuuuN
Ethernet cable - buy from http://fkrt.it/74zMVKNNNN
SD card 16 GB - buy from http://fkrt.it/7PW5LKNNNN
Software requirements:-
Follow below guide for links.
Complete Guide:-
first, of we need 3 softwares to make sd card bootable and rest setup
1 - sd card formatter
download it from the link
https://www.sdcard.org/downloads/form...
plug in your sd card
sd card is ready
2 - win32 diskimager
download it from the link
https://excellmedia.dl.sourceforge.ne...
we need raspbian image file
I have it downloaded
extract it in a folder and keep
it ready
Now
wait for some 5-8 minutes
done writing the image to sd card
now open the sd card partition named as 'boot'
follow me
next, we need to configure IP addresses.
use the software IP scanner to scan ur IP
3 - advanced IP scanner
download it from the link
http://www.advanced-ip-scanner.com/do...
now connect the ethernet cable to Pi and your laptop/desktop
and power it on with the sd card plugged in
wait for 10 seconds
follow my instructions carefully
should be enabled
that's the main IP of pi
now let's see which IP has been assigned using advanced IP scanner
so our pi has been assigned IP as 192.168.137.2
don't change this...
unplug ethernet and close Pi connection
plug in the sd card
open the 'boot' partition
check for a file named as cmdline.txt
add lines at the end
save the file and connect pi again
our sd card is ready now to be booted.
In next phase
we require two more software to use pi on our laptop screen.
1 - Putty
plug in the Pi with ethernet and sd card.
wait 10 seconds
done
first, download it
https://the.earth.li/~sgtatham/putty/...
from the link
now open it
here enter the hostname as from advanced IP scanner and also enable x11.
username as pi
password as raspberry
done.
for next step, we require one more software.
we can use xming or VNC viewer
I will show it with both.
2(a) - VNC viewer
download it
https://www.realvnc.com/download/file...
for address open putty ssh terminal.
type 'vncserver'
done using vnc viewer
cool
next
2(b) - Xming
download it from the link
https://excellmedia.dl.sourceforge.ne...
open it
once opened it will show up in the taskbar
now open putty
type 'lxsession'
done
Now you can easily use pi3 or pi zero with your laptop/desktop using an ethernet cable.
Thank you for watching please like and share.
cool
cool
cool
cool
Смотрите видео Easy way of connecting Raspberry Pi to laptop using Ethernet cable | Beginner Guide онлайн без регистрации, длительностью часов минут секунд в хорошем качестве. Это видео добавил пользователь RoboMex 10 Февраль 2018, не забудьте поделиться им ссылкой с друзьями и знакомыми, на нашем сайте его посмотрели 22,090 раз и оно понравилось 160 людям.