SUBSCRIBE Learn how tile the right way
How to Install Cement board, all the steps you need to know, form cutting and installing to waterproofing. When installing a cement backer board it is important to use the correct kind of screw. Drywall screws are not to be used to install the cement board, due to the composition of the backer board an non coated screw will deteriorate over time and compromise the integrity of the tile installation. A screw that has been coated or galvanized must be used. A screw should be placed every 8", there is going to be a lot of weight when the tile is installed so an adequate number of fasteners should be used. To cut the board to the correct size a simple utility knife is all that is needed. Score the board with the blade of the knife a few times, and then bend the board back until it snaps, complete the cut by running the knife along the cut from the opposite side. A simple key hole saw can be used to make holes for shower valves and escutcheons. The corners and joints will be reinforced with a fiberglass alkali resistant mesh tape and then filled with thinset. Do not use drywall mesh tape. Once the thinset is dry, the walls should be waterproofed with two coats of a liquid applied waterproofing membrane. I will generally reinforce corners of the cement board with fiberglass fabric, then apply two coats of the waterproofing. It is very important to not skip any steps and to be sure that the board, be it Durock, Wonderboard, HardieBaker, or any other type of CBU. Cement board is water safe, but it is not waterproof, so in my opinion the best way to prevent moisture penetration into the wall cavity, is to waterproof the entire surface with a liquid applied waterproofing membrane, in this video Mapei Aquadefense is used for all waterproofing. A Vapor barrier can be used be hind the board in place of the liquid applied waterproofing, however I believe that the membrane directly under the tile gives much superior protection. All tile installed by Sal DiBlasi, Elite-tile Company, in the Boston North Shore area. This video contains affiliate links, which means I will receive a small commission if you click on the product link.
Waterproofing Membrane Fabric http://amzn.to/2kh6XPI
Waterproofing Liquid http://amzn.to/2jFMYHm
☕ Buy me a coffee ☕
https://www.buymeacoffee.com/saldibs2
🙂 This is my Amazon Store 🙂 https://www.amazon.com/shop/saldiblasi
💲1 PDF Floor installation guidelineshttps://sowl.co/s/wWd2d 💲1
Channel Store / @saldiblasi
👍 Patreon / saldiblasi 👍
YouTube Channel / saldibs
Facebook
/ 56681633342
Website
http://www.elitetileco.com/
Twitter
/ saldiblasi1
Instagram
/ saldiblasi1
National Tile Contractors Association
https://tile-assn.site-ym.com/
👇 Some of my favorite Tools 👇
Float https://amzn.to/2tdEpN2
Rubbing Stone https://amzn.to/2QrgRfh
Notched Trowel 1/4 x 1/4 x 1/4-inch https://amzn.to/36bq5mQ
Notched Trowel 1/2 x 1/2 x 1/2-Inch https://amzn.to/2Q5e90g
Notched Trowel 1/4 x 3/8 x 1/4-Inch https://amzn.to/39j1caB
Super Dust Collector – WaleTale https://amzn.to/2MDuVkK
Black Nitrile Gloves - 6 mil https://amzn.to/2SJQ6FZ
Margin Trowel https://amzn.to/352MYHx
Mortar Mixer https://amzn.to/2ZxYqtF
4in Sandpaper for Stone Polishing https://amzn.to/2ZB2skT
Polishing Rubber Backing Pad https://amzn.to/2srikdy
Montolit 63P3 24 Inch Tile Cutter https://amzn.to/2MDoFtl
DEWALT Wet Tile Saw https://amzn.to/2QqpO8O
Rubi Thinset mixer https://amzn.to/39VmNWV
Opt into NTCA’s VIP Text Messaging program for training opportunities.
Text “NTCA” to 31996 or Visit https://widget.smsinfo.io/v2/ae58812b...
For Industry Professionals only
Watch video How to Install Cement board, all the steps needed form cutting and installing to waterproofing. online without registration, duration hours minute second in high quality. This video was added by user Sal DiBlasi 16 September 2017, don't forget to share it with your friends and acquaintances, it has been viewed on our site 1,582,57 once and liked it 11 thousand people.