How to Configure RIP Routing (RIPv1) on Cisco Router in GNS3 | SYSNETTECH Solutions
This video shows you how to configure the Routing Information Protocol (RIP) on Cisco Routers on the GNS3 network simulator program.
✅ S U B S C R I B E ► http://goo.gl/8d0iG9
✅ Article ► https://www.sysnettechsolutions.com/e...
To configure the #RIP Routing:
Step 1: If you have not installed GNS3 before, please refer to the following videos to install it on Windows, Linux, and macOS.
Windows ➦ • How to Install GNS3 2.1 on Windows 10...
Linux / Ubuntu ➦ • How to Install GNS3 VM in VMware Work...
macOS ➦ • How to Install GNS3 on macOS High Sie...
Step 2: After you have done the installation, if you haven't added the #Router IOS image to GNS3 before, please refer to the following video.
Video ➦ • How to Add Cisco Router IOS Images to...
Step 3: Add two Cisco Routers and Cisco Switches to the workspace.
Step 4: Also, add 2 Cloud PCs to the workspace. To add Cloud PC, please refer to the following video.
Video ➦ • How to Configure Cloud in GNS3 | How ...
Step 5: Connect the Cisco Routers with the Serial Interface. And do the Cisco Switch and Cloud PC connections.
Step 6: Run Cisco Routers.
Step 7: Run virtual machines on VMware Workstation connected to Cloud PC.
Step 8: Specify the IP block you want to configure before configuring Rip. (Eg 192.168.1.0/24)
Step 9: Also, configure the IP block of the network connection between the Cisco Routers. (For example 10.1.1.0/24)
Step 10: Open the CLI command prompt on the Cisco Routers and configure the Serial and FastEthernet interfaces.
Step 11: Once you have completed the steps required for RIP Routing, switch to the config mode and add the networks connected to the Routers to the Rip routing table.
Step 12: Perform the following commands as an example to enable the routing information protocol.
R1 (config) # router rip
R1 (config-router) # network 10.1.1.0
R1 (config-router) # 192.168.5.0
R1 (config-router) # end
R2 (config) # router rip
R2 (config-router) # network 10.1.1.0
R2 (config-router) # 192.168.10.0
R2 (config-router) # end
Step 13: Watch the video for the rest of the processes.
Step 14: Don't forget to subscribe to our YouTube channel for more videos on Cisco training with #GNS3!
────EST PRODUCT FOR CISCO TRAINING──────
✅ Buy ► http://bit.ly/CiscoNetworkingDummies
───────────────RELATED VIDEOS───────────────
➊ How to Integrate VMware with GNS3
➦ • How to Integrate GNS3 with VMware Wor...
➋ How to Use VPCS in GNS3
➦ • How to Use VPCS in GNS3 | GNS3 VPCS C...
➌ How to Configure OSPF
➦ • How to Configure OSPF on Cisco Router...
➍ How to Upgrade GNS3 VM
➦ • How to Upgrade GNS3 VM on Windows 10 ...
➎ How to Add Layer 2 Switch
➦ • How to Add Layer 2 Switch in GNS3 | C...
───────────────FOLLOW US───────────────────
✔ Facebook
➦ / sysnettechsolutions
✔ Twitter
➦ / sysnettechs
✔ Pinterest
➦ / sysnettechs
✔ Instagram
➦ / sysnettech_solutions
✔ LinkedIn
➦ / tolqabaqci
███████████████████████████████████████████
Watch video How to Configure RIP Routing (RIPv1) on Cisco Router in GNS3 | SYSNETTECH Solutions online without registration, duration hours minute second in high quality. This video was added by user SYSNETTECH Solutions 07 June 2017, don't forget to share it with your friends and acquaintances, it has been viewed on our site 4,208 once and liked it 57 people.